View MC10H136FN_744007.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10H136 Universal Hexadecimal Counter
Description
The MC10H136 is a high speed synchronous hexadecimal counter. This 10H part is a functional/pinout duplication of the standard MECL 10KTM family part, with 100% improvement in counting frequency and no increase in power-supply current.
Features
http://onsemi.com MARKING DIAGRAMS*
16 MC10H136L AWLYYWW CDIP-16 L SUFFIX CASE 620A 1
* Counting Frequency, 250 MHz Minimum * Power Dissipation, 625 mW Typical * Improved Noise Margin 150 mV * Voltage Compensated * MECL 10K Compatible * Pb-Free Packages are Available*
(Over Operating Voltage and Temperature Range)
16 16 1 PDIP-16 P SUFFIX CASE 648 1 MC10H136P AWLYYWWG
1 20
20 1 PLLC-20 FN SUFFIX CASE 775 A WL YY WW G
10H136G AWLYYWW
= Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package
*For additional marking information, refer to Application Note AND8002/D. *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2006
February, 2006 - Rev. 8
1
Publication Order Number: MC10H136/D
MC10H136
Table 1. FUNCTION SELECT TABLE
CIN X L H L H X S1 L L L H H H S2 L H H L L H Operating Mode Preset (Program) Increment (Count Up) Hold Count Decrement (Count Down) Hold Count Hold (Stop Count) VCC1 Q2 Q3 COUT D3 D2 S2 VEE 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC2 Q1 Q0 CLOCK D0 D1 CIN S1
Table 2. SEQUENTIAL TRUTH TABLE*
INPUTS OUTPUTS S1 S2 D0 D1 D2 D3 Carry Clock Q0 Q1 Q2 Q3 Carry In ** Out L L L L L H H H L X X X L X X X H X X X X X X L X X X X H X X X X X X L X X X X X L L L H H X X L L L L H H H H L H H H H H H H L H L H H H H H L H L H L L H H H H H H H L L H H H H H H H H L L L L H H H H H H H H L L L L H L H H L H H H L H H L H
Pin assignment is for Dual-in-Line Package.
Figure 1. Pin Assignment
LH LH HH LL HL HL HL HL
XX XX XX HH XX XX XX XX
* Truth table shows logic states assuming inputs vary in sequence shown from top to bottom. ** A clock H is defined as a clock input transition from a low to a high logic level.
Table 3. MAXIMUM RATINGS
Symbol VEE VI Iout TA Tstg Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current - Continuous - Surge Characteristic Rating -8.0 to 0 0 to VEE 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C C
Operating Temperature Range Storage Temperature Range - Plastic - Ceramic
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
http://onsemi.com
2
MC10H136
Table 4. ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (Note 1)
0 Symbol IE IinH Characteristic Power Supply Current Input Current High Pins 5, 6, 11, 12, 13 Pin 9 Pin 7 Pin 10 Input Current Low High Output Voltage Low Output Voltage High Input Voltage Low Input Voltage Min - - - - - 0.5 -1.02 -1.95 -1.17 -1.95 Max 165 430 670 535 380 - -0.84 -1.63 -0.84 -1.48 Min - - - - - 0.5 -0.98 -1.95 -1.13 -1.95 25 Max 150 275 420 335 240 - -0.81 -1.63 -0.81 -1.48 Min - - - - - 0.3 -0.92 -1.95 -1.07 -1.95 75 Max 165 275 420 335 240 - -0.735 -1.60 -0.735 -1.45 mA Vdc Vdc Vdc Vdc Unit mA mA
IinL VOH VOL VIH VIL
1. Each MECL 10HTM series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50 W resistor to -2.0 V.
http://onsemi.com
3
MC10H136
Table 5. AC CHARACTERISTICS
0 Symbol tpd Characteristic Propagation Delay Clock to Q Clock to Carry Out Carry in to Carry Out Set-up Time Data (D0 to C) Select (S to C) Carry In (Cin to C) (C to Cin) Hold Time Data (C to D0) Select (C to S) Carry In (C to Cin) (Cin to C) Counting Frequency Rise Time Fall Time Min 0.7 1.0 0.7 2.0 3.5 2.0 0 0 -0.5 0 2.2 250 0.5 0.5 Max 2.3 4.8 2.5 - - - - - - - - - 2.3 2.3 Min 0.7 1.0 0.7 2.0 3.5 2.0 0 0 -0.5 0 2.2 250 0.5 0.5 25 Max 2.4 4.9 2.6 - - - - - - - - - 2.4 2.4 Min 0.7 1.0 0.7 2.0 3.5 2.0 0 0 -0.5 0 2.2 250 0.5 0.5 75 Max 2.5 5.0 2.7 ns - - - - ns - - - - - 2.5 2.5 MHz ns ns Unit ns
tset
thold
fcount tr tf
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously.
S1 9
S2 7 Carry In 10
T T Clock 13
Q0 Q0 C
T T
Q1 Q1 TC
T Q2 T T Q2 TC
T Q3 T T Q3 TTC
VCC1 = Pin 1 VCC2 = Pin 16 VEE = Pin 8
12 D0
14 Q0
11 D1
15 Q1
6 D2
2 Q2
5 D3
3 Q3
4 Carry Out
NOTE: FLIP-FLOPS WILL TOGGLE WHEN ALL T INPUTS ARE LOW.
Figure 2. Logic Diagram
http://onsemi.com
4
MC10H136
APPLICATION INFORMATION The MC10H136 is a high speed synchronous counter that operates at 250 MHz. Counter operating modes include count up, count down, pre-set and hold count. This device allows the designer to use one basic counter for many applications.
ORDERING INFORMATION
Device MC10H136FN MC10H136FNG MC10H136FNR2 MC10H136FNR2G MC10H136L MC10H136P MC10H136PG Package PLLC-20 PLLC-20 (Pb-Free) PLLC-20 PLLC-20 (Pb-Free) CDIP-16 PDIP-16 PDIP-16 (Pb-Free) Shipping 46 Units / Rail 46 Units / Rail 500 / Tape & Reel 500 / Tape & Reel 25 Unit / Rail 25 Unit / Rail 25 Unit / Rail
The S1, S2, control lines determine the operating modes of the counter. In the pre-set mode, a clock pulse is necessary to load the counter with the information present on the data inputs (D0, D1, D2, and D3). Carry out goes low on the terminal count or when the counter is being pre-set.
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
5
MC10H136
PACKAGE DIMENSIONS
20 LEAD PLLC CASE 775-02 ISSUE E
B -N- Y BRK D -L- -M- W D V 0.010 (0.250) T L-M N Z 0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
20
1
X VIEW D-D
G1
S
S
S
A Z R
0.007 (0.180) M T L-M 0.007 (0.180) M T L-M
S
N N
S
S
S
H K1
0.007 (0.180) M T L-M
S
N
S
C
E G G1 0.010 (0.250) S T L-M 0.004 (0.100) J -T- VIEW S
S SEATING PLANE
K F VIEW S 0.007 (0.180) M T L-M
S
N
S
N
S
NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. DIMENSIONS IN INCHES. 3. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
http://onsemi.com
6
MC10H136
PACKAGE DIMENSIONS
CDIP-16 L SUFFIX CERAMIC DIP PACKAGE CASE 620A-01 ISSUE O
B
16
A
9
A
M L
B
1 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. 5 THIS DRAWING REPLACES OBSOLETE CASE OUTLINE 620-10. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01
16X
J
E F C K T N G
16X
0.25 (0.010)
M
TB
SEATING PLANE
D
0.25 (0.010)
M
TA
-A-
16 9
PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R
B
1
8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H K G D
16 PL
SEATING PLANE
J TA
M
M
0.25 (0.010)
M
http://onsemi.com
7
MC10H136
MECL 10H and MECL 10K are trademarks of Motorola, Inc.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
8
MC10H136/D

▲Up To Search▲

Price & Availability of MC10H136FN

	To Download MC10H136FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .